Ruger® LC9s® Optic Mounting Plate
You've asked, we've answered. We present to you the Optic Mount Plate for the LC9S® pistol. Made from aircraft grade aluminum and then hard anodized to mil spec for longevity and scratch resistance, this is the optic mount that you need to bring your LC9S® pistol to the next level. This no gunsmithing required mounting plate is designed to replace your rear sight, no milling of the slide required. Get yours today!
Please refer to the lists below for the 65 Micro and Standard Optics approved for our Optic Plate.
Listing is for the Optic Mount Plate and two 6-32 x 5/16 Hex Flat Head Cap Screws, two 6-32 x 3/8 Hex Button Head Cap Screws, and one 8-32 x 3/16 set screw. *** Optic NOT included ***
*** For the installation of your optic, Blue Locktite is required. Do not use the metric screws that came with your optic, we provide both Button Head Cap screws and Flat Head Cap screws in the correct thread size for our Optic Mount Plate to mount your optic to our plate. Screw head type selection is determined by the type needed for your particular optic. ***
Fits Ruger® LC9s® Pistols. Will NOT fit EC9s® Pistols.
As always, proudly made right here in the USA.
Micro Optics
These Micro Optics are approved for our plate and use the rear set of mounting holes and sit behind the narrow optic location studs.
| JPoint | Romeo Zero | Sightmark Mini |
| Shield RMSc | Romeo X (SORX1200 only) | Riton Tactix MPR D2 |
| Shield SMSc | Romeo X Compact | Riton 3 Tactix MRPD |
| Shield RMS2 | Vortex Defender CCW | HEX Wasp |
| Burris Fastfire C | Holosun 407K | Cyelee CAT Pro |
| Swampfox Sentinel | Holosun 507K | Cyelee CATO-G |
| Swampfox Sentinel II | Holosun SCS Carry | Cyelee X Pro |
| ADE RD3-018 Spike | ADE RD3-030 Apollo Pro | ADE RD3-021 NVWA |
| UTG OP3 Mini Micro | OSight S | Redfield Reveal CD |
| Redfield Ace |
Narrow / Standard Optics
These Narrow, Standard width Optics are approved for our plate and use the forward set of mounting holes and the location studs.
| Vortex Viper | Vector Optics SCRD-19II Frenzy 1x17x24 | HEX Dragonfly |
| Vortex Venom | Docter/Noblex Sight C | Vomz Pilad 1×20 |
| Burris Fastfire 2 | Docter/Noblex sight 2+ | Crimson Trace CT RAD Pro |
| Burris Fastfire 3 | Docter/Noblex sight III | Crimson Trace CTS-1250 |
| Burris Fastfire 4 | Docter/Noblex QUICKsight 5.0 VR | Leica Tempus |
| ADE RD3-003 | Noblex Sight G | UTG OP3 Micro SL |
| ADE RD3-006A Huracan | Delta Optical MiniDot | UTG OP3 Micro (OP-RDM20R and OP-RDM20G only) |
| ADE RD3-006B | Delta Optical MiniDot II | UTG OP3 Micro SLS (Doctor footprint OP-RDM20CTS only) |
| ADE RD3-009 Crusader | Hawke Reflex 1×25 | Cyelee CALF X1 |
| ADE RD3-009-2 | Sightmark Mini Shot Pro Spec | Cyelee CALF V2 |
| ADE RD3-012 Delta | Sightmark Mini Shot M-Spec | Cyelee Cobra X Pro |
| ADE RD3-013 Bertrillium | MAKdot 1×25 | |
| ADE RD3-015 Zantitium | Creative XP GlassEagle HD |
We strive to make all parts we manufacture to be drop in, although there is the rare occasion where a part will HAVE to be fitted to the tolerances of your particular pistol. We cannot control the tolerances of mass produced firearms, therefore we highly suggest that if you run into a tolerance issue to contact us at tech@gallowayprecision.com before taking it to a qualified armorer to fit the part. We also offer installation of all triggers, trigger kits, and parts that we make for a nominal fee.
Specifications
-
Parent SKUGP-OM-LC9s
-
BrandGalloway Precision
-
Country of OriginUSA
-
AssemblyFletcher NC USA
-
Item ConditionBrand new in original packaging
-
Made fromAluminum
Product questions
-
Sep 4, 2024, 11:45
Does this work with the RMSc footprint? I'm trying to mount a AT3 ARO-MINI™ 3 MOA Red Dot Reflex Sight on my LC9S Pro.
https://www.at3tactical.com/products/at3-aro-mini-red-dot-reflex-sight-for-subcompact-pistolsSep 4, 2024, 13:08The rmsc pattern optics use the rear set of 6-32 threaded holes and do not use the location studs.
-
Aug 12, 2024, 00:24
Are these available for the ruger LC9S? Do they fit where the rear sight is located? There is only 1 screw hole but adefinitive groove, is that wher the plate sits?
Aug 12, 2024, 10:27As shown in the pictures they replace the rear sight. You can pick the color finish to see if we have them in stock in that color. If not it should be on our production list.
-
Jun 18, 2024, 21:35
Will this fit a Monstrum Raven SRS Red Dot
Jun 19, 2024, 09:35The optics the plate supports are listed for easy reference in the listing. I've never heard of that optic so we have no info on it nor list it for the plates we offer.
-
Feb 5, 2024, 16:58
Given all the physical variables and your experience, what specific optic do you recommend for use with this on a lc9c?
Are there any problems that I might encounter due to the optic setting a bit higher than if I could mill my slide?Feb 5, 2024, 17:18Customers pick the 507k and romeo optics commonly, both work well. Keep in mind bore over height like in a rifle. The dot will not be impact point due to that and you do not cowitness the dot to the front sight in the plate setups.
-
Dec 13, 2023, 12:56
I’m assuming since this can take the holosun 507k it’s compatible with any of the holosuns with a k footprint correct?
Dec 13, 2023, 13:51Yes the RMSC pattern is supported and any of the units that use that pattern will fit.
Customer reviews
-
Anton DonchevMay 20, 2023, 11:44This plate looks really nice. Unfortunately, doesn't fit LC9S . There is no way to install it ( even with hammer). Emailed support and they told me to use a triangle file for the sides of the plate which helps but now is too loose ( not usable any more). Even the plate "fit" now there is a gap 1-1.5 mm between the base of the plate and the slide of the pistol which doesn't look good.
UPDATE: After this review GP asked me what they can do to make improvements. It turned out that the wrong optic mount plate was sent. Another plate was immediately provided, and I am completely pleased with it. It is a perfect fit for LC9s.
Thanks, GP, for the excellent service and amazing product.
*100% money back (less shipping) on all our products is offered by us against failure of our components or just displeasure our products did not meet your expectations or end needs within the first 30 days. Buy and don't like it, we will refund your purchase price minus shipping upon return, within 30 days of purchase of the complete unmodified parts in question, with the exception of Tool Kits, Tools, Installation Kits, and Closeout products which All Sales are Final. A 20% restocking fee will be applied to returned Triggers, Trigger Kits, Optic Mount Plates, and Guide Rods that have been installed and damaged. Non-installed/non-damaged parts will receive a full refund. If you choose to modify any of our parts without instruction from a Galloway Precision tech, the parts are not eligible for refund or replacement. Refunds are issued upon return within 2 business days back to the original credit card used to purchase the product. We may apply signature required to reduce lost orders for totals over 100.00 or replacement parts or apt addresses.
Despite every effort to provide accurate images of each product’s color and design, actual colors and design may vary slightly, due to different device screen settings, the lighting in the installation location, slight differences in product finishes over time and other factors. Galloway Precision will not accept responsibility for any color or design differences that are not factory faults. When purchasing from Galloway Precision, you agree to accept the small risk that there will be a slight variation between the actual color and design, and the representation on our website. In addition, please be aware that colors and textured finishes often vary between batches; for example slightly different shades of ‘Red’, different degrees of shininess, and different looks and feel for ‘metal/Printed products’ material.
