Optic Mount Plate for Ruger American 45 Compact Pistol

Ruger American 45 Compact Optic Mounting Plate

*** Fits the Ruger American 45 Compact Pistol only. Will not fit Ruger American 9 Compact Pistols.***

We present to you the Optic Mount Plate for the American pistol. Made from aircraft grade aluminum and then hard anodized to mil spec for longevity and scratch resistance, this is the optic mount that you need to bring your American to the next level. This no gunsmithing required mounting plate is designed to replace your rear sight, no milling of the slide required.

You have the choice to mount either a JPoint, Shield RMSc, Shield SMSc, Shield RMS2, Romeo X (SORX1200 only), Vortex Viper, Vortex Venom, Vortex Defender CCW, ADE RD3-003, ADE RD3-006A, ADE RD3-006B, ADE RD3-009, ADE RD3-009-2, ADE RD3-018 Spike, Holosun 507K, Holosun 407K, Holosun SCS Carry, Romeo Zero, Docter/Noblex Sight C, Docter/Noblex sight 2+, Docter/Noblex sight III, Docter/Noblex QUICKsight 5.0 VR, Noblex Sight G, Burris Fastfire C, Burris Fastfire 2, Burris Fastfire 3, Delta Optical MiniDot, Delta Optical MiniDot II, Hawke Reflex 1×25, Sightmark Mini Shot Pro Spec, Sightmark Mini Shot M-Spec, Leica Tempus, MAKdot 1×25, Vector Optics SCRD-19II Frenzy 1x17x24, Creative XP GlassEagle HD, Riton MPR D2, Riton 3 Tactix MPRD, Swampfox Sentinal, HEX Dragonfly, HEX Wasp, Crimson Trace CT RAD Pro, Crimson Trace CTS-1550, Crimson Trace CTS-1250, Cyelee CALF V2, Cyelee CAT PRO, or Vomz Pilad 1×20.

*** The JPoint, Shield RMSc, Shield SMSc, Shield RMS2, Burris Fastfire C, Romeo Zero, Romeo X (SORX1200 only), Vortex Defender CCW, Holosun 507K, Holosun 407K, Holosun SCS Carry, Sightmark Mini, Riton MPR D2, Riton 3 Tactix MPRD, Swampfox Sentinal, HEX Wasp, Cyelee CAT PRO, Crimson Trace CTS-1550, and ADE RD3-018 Spike mount using the rear set of mounting holes and do not use the locating pins at the front of the plate. ***

Get yours today!

Listing is for one Optic Mount Plate, two 6-32 x 5/16 Hex Flat Head Cap Screws, two 6-32 x 1/2 Hex Flat Head Cap Screws, and two 6-32 x 3/8 Hex Button Head Cap Screws. *** Optic NOT included ***

*** For the installation of your optic, Blue Locktite is required. Remove the pre-installed optic mounting screws from our plate before sliding the plate in the dovetail of your slide. This is a snug fitting plate and will need to be tapped in place using a hard rubber or nylon hammer. With Blue Loctite snug up the center set screw securing the plate to the slide. When installing the optic on the plate do NOT use the metric screws that came with your optic, we provide both Button Head Cap screws and Flat Head Cap screws in the correct thread size for our Optic Mount Plate to mount your optic to our plate. Again, Blue Loctite should be used to secure the our optic screws to our plate. Screw head type selection is determined by the type needed for your particular optic.  ***

Available in Black.

Fits the Ruger® American 45 Compact Pistol only. *** Does not fit American Full Size, American 9 Compact, American Competition model, LC9s, EC9s, LCP, or any other Ruger Pistol.***

As always, proudly made right here in the USA.

We strive to make all parts we manufacture to be drop in, although there is the rare occasion where a part will HAVE to be fitted to the tolerances of your particular pistol. We cannot control the tolerances of mass produced firearms, therefore we highly suggest that if you run into a tolerance issue to contact us at tech@gallowayprecision.com before taking it to a qualified armorer to fit the part. We also offer installation of all triggers, trigger kits, and parts that we make for a nominal fee.