Optic Mount Plate for Smith & Wesson M&P 9 Shield EZ and Shield EZ 30 Super Carry Pistols
Options:
Optic Mounting Plate for Smith & Wesson M&P 9 Shield EZ and Shield EZ 30 Super Carry Pistols
Introducing the Optic Mount Plate for 9 EZ / EZ 30 Super Carry pistols. Made from aircraft grade aluminum and then hard anodized to mil spec for longevity and scratch resistance, this is the optic mount that you need to bring your EZ to the next level. Now available in Black or Red anodized finish. This no gunsmithing required mounting plate is designed to replace your rear sight, no milling of the slide required.
Please refer to the lists below for the 65 Micro and Standard Optics approved for our Optic Mount Plate.
Get yours today!
Listing is for the Optic Mount Plate and two 6-32 x 5/16 Hex Flat Head Cap Screws, two 6-32 x 1/2 Hex Flat Head Cap Screws, two 6-32 x 3/8 Hex Button Head Cap Screws. *** Optic NOT included ***
*** For the installation of your optic, Blue Locktite is required. The original rear sight mounting screw is reused from underneath the slide, same as factory. Do not use the metric screws that came with your optic, we provide both Button Head Cap screws and Flat Head Cap screws in the correct thread size for our Optic Mount Plate to mount your optic to our plate. Screw head type selection is determined by the type needed for your particular optic. ***
Fits Smith & Wesson M&P 9 Shield EZ and Shield EZ 30 Super Carry Pistols.
As always, proudly made right here in the USA.
Micro Optics
These Micro Optics are approved for our plate and use the rear set of mounting holes and sit behind the narrow optic location studs.
| JPoint | Romeo Zero | Sightmark Mini |
| Shield RMSc | Romeo X (SORX1200 only) | Riton Tactix MPR D2 |
| Shield SMSc | Romeo X Compact | Riton 3 Tactix MRPD |
| Shield RMS2 | Vortex Defender CCW | HEX Wasp |
| Burris Fastfire C | Holosun 407K | Cyelee CAT Pro |
| Swampfox Sentinel | Holosun 507K | Cyelee CATO-G |
| Swampfox Sentinel II | Holosun SCS Carry | Cyelee X Pro |
| ADE RD3-018 Spike | ADE RD3-030 Apollo Pro | ADE RD3-021 NVWA |
| UTG OP3 Mini Micro | OSight S | Redfield Reveal CD |
| Redfield Ace |
Narrow / Standard Optics
These Narrow, Standard width Optics are approved for our plate and use the forward set of mounting holes and the location studs.
| Vortex Viper | Vector Optics SCRD-19II Frenzy 1x17x24 | HEX Dragonfly |
| Vortex Venom | Docter/Noblex Sight C | Vomz Pilad 1×20 |
| Burris Fastfire 2 | Docter/Noblex sight 2+ | Crimson Trace CT RAD Pro |
| Burris Fastfire 3 | Docter/Noblex sight III | Crimson Trace CTS-1250 |
| Burris Fastfire 4 | Docter/Noblex QUICKsight 5.0 VR | Leica Tempus |
| ADE RD3-003 | Noblex Sight G | UTG OP3 Micro SL |
| ADE RD3-006A Huracan | Delta Optical MiniDot | UTG OP3 Micro (OP-RDM20R and OP-RDM20G only) |
| ADE RD3-006B | Delta Optical MiniDot II | UTG OP3 Micro SLS (Doctor footprint OP-RDM20CTS only) |
| ADE RD3-009 Crusader | Hawke Reflex 1×25 | Cyelee CALF X1 |
| ADE RD3-009-2 | Sightmark Mini Shot Pro Spec | Cyelee CALF V2 |
| ADE RD3-012 Delta | Sightmark Mini Shot M-Spec | Cyelee Cobra X Pro |
| ADE RD3-013 Bertrillium | MAKdot 1×25 | |
| ADE RD3-015 Zantitium | Creative XP GlassEagle HD |
We strive to make all parts we manufacture to be drop in, although there is the rare occasion where a part will HAVE to be fitted to the tolerances of your particular pistol. We cannot control the tolerances of mass produced firearms, therefore we highly suggest that if you run into a tolerance issue to contact us at tech@gallowayprecision.com before taking it to a qualified armorer to fit the part. We also offer installation of all triggers, trigger kits, and parts that we make for a nominal fee.
Specifications
-
Parent SKUGP-OM-9EZ
-
BrandGalloway Precision
-
Country of OriginUSA
-
AssemblyFletcher NC USA
-
Item ConditionBrand new in original packaging
-
Made fromAluminum
-
Product classGalloway Precision Product
-
AnodizingBlack, Red
- Manufacturers
-
ManufacturerGalloway Precision
-
Product questions
-
Apr 24, 2025, 13:30
Do you have shield ez 9mm optic mount plate that will accommodate a Holosun 407k red dot?
Apr 24, 2025, 15:04That is a supported and listed optic, check the listing for install info on it as it does not use the location studs.
-
Mar 22, 2025, 10:09
Will it work with olight osight 3moa
Mar 24, 2025, 09:26We do not have any footprint info on that sight. I recommend picking from the listing info, we have over 70 to pick from.
-
Mar 17, 2025, 17:25
does this work with the LCI installed still ?
Mar 18, 2025, 08:15Yes.
-
Feb 13, 2025, 16:00
I have a S&W M&P EZ 9mm, I bought Bushnell RXS-250 will it work with EZ 9mm and red dot sight? Thanks TL
I have a adapter plate in cart ready to go and it says 380 MP EZ. Please advise,.... Thx TLFeb 14, 2025, 07:58No our plates list what will bolt down in the listing info, these are not supported since they use the delta point pattern. I suggest picking from the listing we have over 60 to pick from listed there.
-
Feb 10, 2025, 19:19
Do you have shield ez 9mm optic mount plate that will accommodate a Holosun 407c red dot?
Feb 11, 2025, 09:16No we do not offer a plate for the EZ pistol line that will support the RMR pattern sorry.
Customer reviews
-
Steven SawyerDec 2, 2024, 05:19Came faster than expected and installed amazingly easy! Very well-made and now completes my M&P with optics that it otherwise would not have had.
-
R HammonsSep 7, 2024, 16:05Great find. I wanted to add a red dot to my S&W Shield EZ 30 Super Carry, but could not find a mount other than one poorly rated. This mount is nicely machined and fits perfectly in the rear sight cavity (no give). I added a Burris Fastfire C red dot and I am very happy with the results. The fact that GP lists all of the optics that will fit on the mount was extremely helpful in down-selecting to the optic desired. Definitely recommended.
-
Danny HermosilloJul 17, 2023, 13:41I bought an optic mount plate from an Amazon vendor that claimed to fit my Shield EZ. It did not. Had to force it on, and screws did not line up. I returned it, and bought this mount, and it fit my Shield EZ 30 Super Carry like a glove. Slid right in. And it was about half the price of the Amazon mount! Thanks, Galloway.
-
WillFeb 19, 2022, 21:04Was looking for a red dot but not really any options for the EZ... until now. This mounting plate literally takes 2 minutes to install and as long as you use one of the specified optics, it fits perfectly. Thanks for a much needed product!
*100% money back (less shipping) on all our products is offered by us against failure of our components or just displeasure our products did not meet your expectations or end needs within the first 30 days. Buy and don't like it, we will refund your purchase price minus shipping upon return, within 30 days of purchase of the complete unmodified parts in question, with the exception of Tool Kits, Tools, Installation Kits, and Closeout products which All Sales are Final. A 20% restocking fee will be applied to returned Triggers, Trigger Kits, Optic Mount Plates, and Guide Rods that have been installed and damaged. Non-installed/non-damaged parts will receive a full refund. If you choose to modify any of our parts without instruction from a Galloway Precision tech, the parts are not eligible for refund or replacement. Refunds are issued upon return within 2 business days back to the original credit card used to purchase the product. We may apply signature required to reduce lost orders for totals over 100.00 or replacement parts or apt addresses.
Despite every effort to provide accurate images of each product’s color and design, actual colors and design may vary slightly, due to different device screen settings, the lighting in the installation location, slight differences in product finishes over time and other factors. Galloway Precision will not accept responsibility for any color or design differences that are not factory faults. When purchasing from Galloway Precision, you agree to accept the small risk that there will be a slight variation between the actual color and design, and the representation on our website. In addition, please be aware that colors and textured finishes often vary between batches; for example slightly different shades of ‘Red’, different degrees of shininess, and different looks and feel for ‘metal/Printed products’ material.
